Putting in a drain pipe for a washer could appear to be a frightening job, however with the suitable instruments and slightly little bit of know-how, it may be a manageable DIY undertaking. Whether or not you are changing an previous drain pipe or putting in one for the primary time, following a step-by-step information will guarantee a profitable set up.
Step one is to assemble the required instruments and supplies. You will want a drain pipe, a drain clamp, a hacksaw, a screwdriver, and a pair of pliers. After you have your instruments and supplies, you possibly can start the set up course of. First, find the drain outlet on the washer. It is often situated on the backside of the again of the machine. Measure the gap from the drain outlet to the ground drain. Minimize the drain pipe to the measured size utilizing the hacksaw.
Subsequent, connect the drain clamp to the drain pipe. The drain clamp will assist to safe the drain pipe to the drain outlet. Place the drain pipe over the drain outlet and tighten the drain clamp utilizing the screwdriver. Lastly, join the opposite finish of the drain pipe to the ground drain. Use the pliers to tighten the connection. As soon as the drain pipe is linked, activate the washer and test for leaks. If there are not any leaks, the set up is full.
Planning and Preparation
Earlier than embarking on the duty of putting in a drain pipe to your washer, it’s important to plan and put together meticulously. This part will present a complete information that will help you lay the groundwork for a profitable set up:
1. Gathering Supplies and Instruments
Step one is to assemble all the required supplies and instruments. Here’s a complete listing to make sure you have every thing you want:
Supplies:
| Merchandise | Amount |
|---|---|
| Versatile drain hose | 6-8 toes |
| Hose clamp | 1-2 |
| Drain pipe lure (elective) | 1 |
Instruments:
- Adjustable wrench
- Pliers
- Screwdriver
- Measuring tape
- Stage (elective)
2. Figuring out the Drain Location
Subsequent, you could decide the placement of the drain the place you’ll join the drain pipe. There are two widespread choices:
- Standpipe: A standpipe is a vertical pipe that extends from the ground or wall. It’s the best choice in case your washer is close to a rest room or utility room.
- Low-profile drain: Any such drain is situated under the ground degree. It’s typically utilized in tight areas or when the washer is in a basement.
3. Measuring and Chopping the Drain Pipe
Now, you could measure and reduce the drain pipe to the suitable size. To do that, observe these steps:
- Measure the gap from the washer outlet to the drain. Enable for just a few additional inches for slack.
- Mark the measurement on the drain pipe utilizing a marker or tape.
- Use a pointy utility knife or pipe cutter to chop the drain pipe to the marked size.
Gathering Supplies
1. Measuring Tape or Ruler
- To precisely measure the size of the supplies required for the set up.
2. Drain Hose
Forms of Drain Hose:
| Kind | Description |
|---|---|
| Corrugated Drain Hose | Versatile, expandable hose for brief distances and high-pressure functions. |
| Stable Drain Hose | Inflexible, non-expandable hose for longer distances and lower-pressure functions. |
– Size: Measured from the washer’s drain outlet to the specified drain connection level.
– Diameter: Usually 1-1/2 inches or 1-3/4 inches, matching the washer’s drain outlet.
3. Drain Clamp
Forms of Drain Clamps:
| Kind | Description |
|---|---|
| Hose Clamp | Adjustable metallic or plastic clamp for securing the drain hose to the washer and the drain connection level. |
| Spring Clamp | Pre-formed metallic clamp with a spring mechanism for simple set up and elimination. |
– Dimension: Suitable with the diameter of the drain hose.
4. P-Lure (Elective)
- A U-shaped pipe put in beneath the sink or different drain connection level to stop sewer gases from coming into the house.
5. Drain Connection Elbow
- A curved becoming that connects the drain hose to the drain pipe or P-trap.
6. Screwdriver
- For tightening the drain clamp.
7. Wrench (Elective)
- For loosening or tightening the drain connection elbow or P-trap.
Selecting the Drain Location
Deciding on the best drain location is essential for environment friendly water drainage out of your washer. Listed here are some components to think about when selecting the drain:
-
Proximity to the Machine:
Select a drain that’s near the washer to reduce the size of the drain hose and cut back the danger of kinks or clogs.
-
Gravity Drainage:
Gravity ought to help in draining the water. The drain needs to be situated at a decrease elevation than the machine’s drain pump to make sure correct water move.
-
Code Compliance:
Adjust to native constructing codes and rules relating to the placement and set up of drain pipes. These codes could specify the minimal distance from different fixtures, partitions, and ceilings.
Code Requirement Clarification Minimal Distance from Wall Usually 6 inches to stop harm to partitions from water leakage. Most Distance from Drain Lure Often 8 toes to keep away from water accumulation and odor buildup. Enough Slope 1/4-inch slope per foot to facilitate correct drainage. -
Accessibility:
Make sure that the drain is accessible for future upkeep or repairs. Think about using a drain lure that’s simple to scrub or exchange.
-
Aesthetics:
Think about the looks of the drain and its affect on the general aesthetics of the area. Disguise the drain hose or use a discreet drain cowl to take care of a tidy look.
- Examine the Hose: Examine the drain hose for any harm or kinks. If any defects are current, exchange the hose with a brand new one.
- Place the Hose: Place the drain hose into the designated drain pipe. Guarantee it’s totally inserted to stop any leaks.
- Use a Hose Clamp: Tighten a hose clamp across the connection level of the drain hose and drain pipe. Safe the clamp firmly to create a watertight seal.
- Double-Examine the Connection: To make sure a safe connection, tug on the drain hose gently. If it stays firmly connected, the connection is safe.
- Safe Free Ends: If there are any extra lengths of the drain hose, use a cable tie or zip tie to safe them neatly.
- Repair Further Assist: For added stability, contemplate putting in a drain hose assist bracket or hook close to the drain pipe. This can forestall the hose from sagging or changing into disconnected.
- Examine for Leaks: Run a take a look at cycle of the washer and observe the drain pipe connection. If there are not any leaks or water drips, the set up is profitable.
- Examine for Leaks
-
If you happen to discover a leak:
- Tighten the drain hose clamp on the drain pipe connection.
- Make sure the drain hose is securely connected to each the washer and the drain pipe.
- If the leak persists, contact a professional plumber for additional help.
-
If there are not any leaks:
- Your drain pipe is efficiently put in and examined.
- Proceed to reconnect the washer to {the electrical} outlet and water provide.
- Run a daily wash cycle to confirm that every thing is functioning appropriately.
- A drain pipe
- A hose clamp
- A screwdriver
- A putty knife
- A bucket
- Begin by turning off the water provide to the washer.
- Subsequent, find the drain hose on the washer. The drain hose is usually situated in the back of the machine, close to the underside.
- Disconnect the drain hose from the washer by loosening the hose clamp with a screwdriver.
- Insert the drain pipe into the drain hose. The drain pipe ought to match snugly into the hose.
- Tighten the hose clamp to safe the drain pipe to the hose.
- Find the drainpipe outlet. The drainpipe outlet is usually situated on the wall or within the ground close to the washer.
- Insert the drain pipe into the drainpipe outlet.
- Tighten the hose clamp to safe the drain pipe to the outlet.
- Activate the water provide to the washer.
- Examine for leaks. If you happen to see any leaks, tighten the hose clamps till the leaks cease.
Putting in the Drain Hose
As soon as the standpipe is safe, you possibly can connect the drain hose. The top of the drain hose that connects to the standpipe will usually have a rubber gasket or O-ring. Be sure that the gasket is correctly seated within the standpipe earlier than tightening the hose clamp.
To connect the opposite finish of the drain hose to the washer, merely push it onto the drain outlet pipe. Once more, be certain that the hose is securely connected by tightening the hose clamp.
Securing the Drain Hose
As soon as the drain hose is connected, you could safe it in order that it does not come free and trigger a leak. There are just a few alternative ways to do that.
Utilizing a Drain Hose Strap
A drain hose strap is a straightforward and cheap technique to safe the drain hose. To make use of a drain hose strap, merely wrap the strap across the hose and tighten the buckle.
Utilizing a Zip Tie
A zipper tie is another choice for securing a drain hose. To make use of a zipper tie, merely wrap the tie across the hose and pull it tight. Minimize off the surplus tie utilizing a pair of scissors.
Utilizing a Screw
In some circumstances, you might be able to safe the drain hose by screwing it into a close-by wall stud or cupboard. To do that, merely drill a pilot gap within the stud or cupboard and insert a screw.
As soon as the drain hose is secured, you possibly can activate the water provide to the washer and test for leaks. If there are not any leaks, you are completed!
| Technique | Execs | Cons |
|---|---|---|
| Drain Hose Strap | Cheap. Straightforward to make use of. | Will not be robust sufficient for heavy-duty hoses. |
| Zip Tie | Robust and sturdy. Straightforward to make use of. | Might be troublesome to take away if you could exchange the hose. |
| Screw | Most safe methodology. | Requires drilling a gap within the wall or cupboard. |
Securing the Hose
To make sure a safe connection between the drain hose and the drain pipe, observe these detailed steps:
Testing the Drain
As soon as the drain pipe is put in, it is essential to check it for leaks. Run the washer on a brief cycle and observe the drain pipe and connections for any indicators of water leakage.
| Leak Examine Factors |
|---|
| Drain hose clamp tightness |
| Safe attachment at each the washer and drain pipe |
| Absence of water leakage throughout a brief wash cycle |
Troubleshooting Frequent Points
No Drainage
Doable Causes:
1. Clogged drain hose
2. Airlock within the drain hose
3. Kinked or crushed drain hose
4. Defective drain pump
Options:
1. Examine and clear the drain hose for obstructions.
2. Straighten out any kinks or crushes within the drain hose.
3. Strive disconnecting and reconnecting the drain hose to get rid of any airlocks.
4. If the drain pump is suspected to be defective, it could must be changed.
Gradual Drainage
Doable Causes:
1. Partially blocked drain hose
2. Restricted drain filter
3. Overloaded washer
Options:
1. Clear the drain hose completely to take away any partial blockages.
2. Take away the drain filter and clear it completely.
3. Keep away from overloading the washer, as this may pressure the drain system.
Leaking Drain Hose
Doable Causes:
1. Free or broken connections
2. Cracks or holes within the drain hose
3. Incorrectly put in or routed drain hose
Options:
1. Examine the connections at each ends of the drain hose and tighten if vital.
2. Examine the drain hose for any cracks or holes and exchange it if broken.
3. Be sure that the drain hose is routed correctly and never obstructed by any objects.
Upkeep and Care
To make sure the longevity and correct functioning of your washer drain pipe, common upkeep and care are important. Listed here are some key steps to observe:
Month-to-month Cleansing
Take away the drain hose from the drainpipe and flush it completely with scorching water. Use a drain cleaner or vinegar resolution to take away any buildup or clogs.
Quarterly Inspection
Examine the whole size of the drain pipe for any leaks, cracks, or harm. If any points are discovered, restore or exchange the affected part promptly.
Annual Deep Cleansing
Disconnect the drain pipe from the washer and drain valve. Use a drain cleansing instrument or a robust water jet to completely clear the whole system and take away any gathered particles.
Sustaining the Air Hole
The air hole is a small area between the tip of the drain hose and the drainpipe that forestalls wastewater from flowing again into the washer. Frequently test the air hole for obstructions and clear it if vital.
| Common Upkeep Schedule |
|---|
| Month-to-month: Cleansing |
| Quarterly: Inspection |
| Yearly: Deep Cleansing and Air Hole Upkeep |
Further Ideas for Care
Keep away from pouring harsh chemical compounds or bleach instantly into the drain pipe. Use a bucket or funnel to keep away from damaging the fabric.
Examine the producer’s directions for any particular care or upkeep necessities associated to your washer drain pipe.
By following these upkeep and care tips, you possibly can guarantee the sleek and environment friendly operation of your washer drain pipe for years to return.
How To Set up A Drain Pipe For Washing Machine
Putting in a drain pipe for a washer is a comparatively easy job that may be accomplished in just a few hours. Nevertheless, you will need to observe the directions fastidiously to make sure that the set up is completed appropriately and that the washer operates correctly.
To put in a drain pipe for a washer, you have to the next supplies:
After you have gathered your supplies, you possibly can start the set up course of.
Folks Additionally Ask About How To Set up A Drain Pipe For Washing Machine
How a lot does it price to put in a drain pipe for a washer?
The fee to put in a drain pipe for a washer will fluctuate relying on the complexity of the set up and the supplies used. Nevertheless, most owners can anticipate to pay between $50 and $150 for the set up.
Can I set up a drain pipe for a washer myself?
Sure, putting in a drain pipe for a washer is a comparatively easy job that may be accomplished by most owners with fundamental plumbing abilities. Nevertheless, in case you are not comfy working with plumbing, it’s best to rent a professional plumber to do the set up for you.
What sort of drain pipe ought to I take advantage of for a washer?
The kind of drain pipe you need to use for a washer will rely upon the particular washer you might have and the structure of your property. Nevertheless, PVC pipe is an effective possibility for many washing machines.
