If you happen to’re an avid gamer, chances are high you have come throughout the Xbox 1, Microsoft’s well-liked gaming console. Nonetheless, there could come a time when you’ll want to open up your Xbox 1 for repairs or cleansing. Whereas it might seem to be a frightening job, it is truly fairly easy with the correct instruments and directions.
Initially, collect the required instruments. You will want a Torx T10 screwdriver and a plastic spudger or opening software. Upon getting your instruments prepared, you possibly can start the method of opening up your Xbox 1. Begin by putting the console on a flat floor and eradicating the ability twine. Subsequent, find the 2 Torx T10 screws on the again of the console and take away them. These screws are situated close to the underside of the console, on both aspect of the ability port.
As soon as the screws are eliminated, you possibly can fastidiously use the plastic spudger or opening software to pry open the case. Begin by inserting the software into the seam between the highest and backside halves of the case, and gently work your approach across the console. Watch out to not apply an excessive amount of pressure, as you could possibly harm the case. As soon as the case is open, you’ll have entry to the interior parts of your Xbox 1.
Disassembling the Xbox One Chassis
Getting ready Your Workspace
Earlier than disassembly, it is essential to organize an acceptable workspace. Select a secure, well-lit space with ample area to unfold out the parts. Collect the required instruments, together with a Torx T10 screwdriver, a Phillips #00 screwdriver, tweezers, and a non-static fabric. Guarantee you’ve a transparent understanding of the disassembly directions to keep away from potential harm.
Eradicating the High Cowl
Find the 2 Torx T10 screws on the rear of the console, hidden by rubber covers. Take away these screws and gently raise the highest cowl upwards. Proceed with warning to keep away from damaging any wires or cables. Unplug the ability cable and any linked peripherals.
Eradicating the Backside Panel
Flip the console over and find the 4 Phillips #00 screws on the underside. Take away these screws and thoroughly slide the underside panel in the direction of the entrance. It ought to come free, revealing the interior parts. Use tweezers to disconnect any free wires or connectors on the underside panel.
Eradicating the Plastic Defend
The plastic defend covers numerous parts, such because the fan, warmth sink, and energy provide. Use tweezers to disconnect the 2 wires connecting to the defend. Then, gently raise the plastic defend upwards to take away it. Be aware that some fashions could have extra screws or clips holding the defend in place, which ought to be eliminated accordingly.
Eradicating the Energy Provide
Establish the ability provide unit situated on the backside proper of the console. Disconnect any cables connecting to the ability provide, together with the principle energy cable, and take away the 2 Phillips #00 screws securing it. Fastidiously raise the ability provide out of the chassis.
Eradicating the Fan and Warmth Sink Meeting
Unplug the fan from the motherboard and take away the 4 screws holding the fan and warmth sink meeting. Fastidiously raise the meeting upwards and set it apart.
Eradicating the Motherboard
Disconnect all remaining cables and connectors on the motherboard, together with the ability connector, SATA cable, and different peripherals. Find the six Torx T10 screws securing the motherboard and take away them. Gently raise the motherboard out of the chassis, taking care to not harm any parts or wires.
| Step | Motion |
|---|---|
| 1 | Take away Torx T10 screws from rear and raise prime cowl |
| 2 | Take away Phillips #00 screws and slide backside panel ahead |
| 3 | Disconnect wires and raise plastic defend |
| 4 | Disconnect cables and take away energy provide |
| 5 | Disconnect fan and take away fan and warmth sink meeting |
| 6 | Disconnect cables and take away motherboard |
Eradicating the Exterior Screws
Find the 12 exterior screws on the again of the Xbox One. They’re organized in 4 rows of three screws every. Use a T10 Torx screwdriver to take away the screws.
Extra Particulars
When eradicating the screws, watch out to not strip the screw heads. If you happen to encounter any resistance, apply light strain and check out once more.
Preserve monitor of the screws as you take away them. They don’t seem to be all the identical dimension, so you will need to put them again of their right places.
As soon as the exterior screws are eliminated, the highest panel of the Xbox One will be lifted off. Watch out to not harm the cables which are connected to the highest panel.
| Screw Location | Screw Dimension |
|---|---|
| High row | 10mm |
| Second row | 12mm |
| Third row | 10mm |
| Backside row | 12mm |
Unplugging Inner Cables
Earlier than you possibly can take away the interior parts of your Xbox One, you have to to unplug the next cables:
- Energy cable
- HDMI cable
- Ethernet cable (if linked)
- Kinect sensor cable (if linked)
To unplug the ability cable, merely grasp it firmly and pull it straight out of the again of the console. To unplug the HDMI cable, press the discharge button on the aspect of the connector after which pull it out. To unplug the Ethernet cable, merely pull it out of the again of the console. To unplug the Kinect sensor cable, press the discharge button on the aspect of the connector after which pull it out.
Unplugging the Inner Energy Provide
Upon getting unplugged the exterior cables, you possibly can start unplugging the interior energy provide. To do that, you have to a Torx T10 screwdriver.
Step 1: Take away the screws
Use the Torx T10 screwdriver to take away the 2 screws that safe the ability provide to the chassis. The screws are situated on the again of the console, close to the ability enter.
Step 2: Unplug the ability provide
As soon as the screws are eliminated, you possibly can unplug the ability provide from the motherboard. To do that, merely grasp the ability provide by the connector and pull it straight out of the motherboard.
Step 3: Take away the ability provide
As soon as the ability provide is unplugged, you possibly can take away it from the chassis. To do that, merely raise the ability provide straight up and out of the chassis.
| Step | Motion |
|---|---|
| 1 | Take away the screws that safe the ability provide to the chassis. |
| 2 | Unplug the ability provide from the motherboard. |
| 3 | Take away the ability provide from the chassis. |
Disconnecting Energy Provide
1. Security Precautions
Earlier than dealing with any electrical tools, it is important to take security precautions. Guarantee that you’re engaged on a secure and dry floor, and disconnect the Xbox One from any energy sources.
2. Find the Energy Provide
The ability provide unit (PSU) is usually situated on the rear of the Xbox One console. It is a black field with an influence inlet and numerous cables connected to it.
3. Unplug the Energy Cable
Find the ability cable linked to the PSU and gently pull it straight out. Don’t yank or bend the cable excessively.
4. Eradicating the PSU Screws
The PSU is secured to the Xbox One chassis with two screws. These screws are sometimes Phillips head and situated on the edges of the PSU.
Be aware: It is essential to make use of the proper screwdriver dimension and to keep away from overtightening or stripping the screws.
| Screw Location | Description |
|---|---|
| Left aspect of PSU | Close to the ability cable inlet |
| Proper aspect of PSU | Near the sting of the Xbox One chassis |
5. Eradicating the PSU
As soon as the screws are eliminated, gently slide the PSU in the direction of the again of the console and raise it out to disconnect it utterly. Watch out to not harm the PSU or some other parts whereas doing so.
Eradicating Motherboard Defend
Find and take away the seven T9 Torx screws securing the motherboard defend.
Slide the motherboard defend straight up and off of the Xbox One.
Disconnecting the Entrance Panel Cables
Fastidiously disconnect the next cables from the motherboard:
| Cable | Connector on Motherboard |
|---|---|
| Disc Drive Energy Cable | JP11 |
| Entrance Panel Board Cable | JP12 |
| Energy Provide Cable | JP13 |
| USB Drive Cable | JP14 |
| HDMI Cable | JP15 |
| Wi-Fi Antenna Cables | JP17 and JP18 |
Eradicating the Motherboard
Find and take away the six T8 Torx screws securing the motherboard to the console chassis.
Fastidiously raise the motherboard up and out of the console chassis, being conscious of the cables nonetheless linked to it.
Exposing the Motherboard
To reveal the motherboard, you may have to take away the next parts:
1. High Cowl
Use a plastic pry software to softly pry off the highest cowl, beginning close to the disc slot and dealing your approach across the edges.
2. Warmth Sink
Disconnect the warmth sink fan and take away the screws holding down the warmth sink. Raise the warmth sink straight as much as take away it.
3. Energy Provide Unit (PSU)
Disconnect the ability cables and take away the screws securing the PSU. Slide the PSU out in the direction of the again of the console.
4. Optical Drive
Disconnect the ability and knowledge cables from the optical drive. Take away the screw holding the drive in place and slide it out in the direction of the entrance of the console.
5. Onerous Drive
Disconnect the ability and knowledge cables from the laborious drive. Take away the screws holding the drive in place and slide it out in the direction of the again of the console.
6. Motherboard
Disconnect the remaining cables from the motherboard, together with the ability button, fan headers, and entrance panel connectors.
Find the screws securing the motherboard to the chassis and take away them.
Fastidiously raise the motherboard out of the chassis.
| Screw Location | Amount |
|---|---|
| High of Motherboard | 4 |
| Backside of Motherboard | 2 |
| Sides of Motherboard | 1 every |
Detaching the Optical Drive
Step 7: Fastidiously disconnect the cables and detach the optical drive:
- Establish the 2 SATA cables and energy cable linked to the optical drive.
- Gently pull the SATA cables straight as much as disconnect them from the drive.
- Disconnect the ability cable from the drive by urgent the discharge tab and pulling it out.
- Find the 4 screws securing the optical drive to the chassis.
- Use a screwdriver to unscrew the 4 screws.
- Raise the optical drive barely on the entrance nook and slide it in the direction of the again of the console to detach it.
- Be conscious of any cables which will change into entangled throughout this course of.
As soon as the optical drive is indifferent, you possibly can change it with a brand new one or carry out any crucial repairs.
Eradicating the Warmth Sink
Now that you’ve eliminated the highest cowl, you have to to take away the warmth sink. This can be a massive metallic plate that’s connected to the motherboard with 4 screws. Please discuss with the picture under for the screw location.
Screw Location for Warmth Sink
| Screw Location |
|---|
| 1. High left |
| 2. High proper |
| 3. Backside left |
| 4. Backside proper |
Upon getting situated all 4 screws, use a screwdriver to take away them. Watch out to not lose any of the screws, as you have to them to reassemble the Xbox One later.
As soon as the screws are eliminated, you must be capable to raise the warmth sink off the motherboard.
Accessing the Inner Elements
To delve into the interior workings of your Xbox One, you may have to dismantle it cautiously. Observe these steps to achieve entry to its inside parts.
1. Collect Instruments: Purchase a Torx T10 screwdriver, a flathead screwdriver, and a spudger software.
2. Take away Backside Cowl: Use the Torx T10 screwdriver to take away the eight screws securing the underside cowl. Gently pry the quilt away with the flathead screwdriver.
3. Disconnect Battery: Find the battery connector close to the entrance of the console. Use the flathead screwdriver to fastidiously disconnect it.
4. Take away Rear Panel: Unscrew the 4 Torx T10 screws holding the rear panel. Slide the panel in the direction of the entrance and raise it upwards.
5. Take away Energy Provide: Disconnect the ability provide connector from the motherboard. Use the Torx T10 screwdriver to take away the 4 screws securing the ability provide and gently raise it out.
6. Take away High Cowl: Disconnect the ribbon cable connecting the highest cowl to the motherboard. Use the Torx T10 screwdriver to take away the six screws holding the highest cowl. Fastidiously raise the quilt off.
7. Disconnect Entrance Panel: Unplug the entrance panel ribbon cable from the motherboard. Use the spudger software to softly pry the entrance panel away from the console.
8. Take away Optical Drive: Use the Torx T10 screwdriver to take away the 4 screws securing the optical drive. Slide the drive out in the direction of the entrance and take away it.
9. Entry Motherboard: As soon as the optical drive is eliminated, you may have entry to the motherboard and different inside parts. You may additional disassemble the console by eradicating the heatsink, fan, and different parts as wanted. Nonetheless, proceed with warning to keep away from damaging delicate components.
Reassembling the Xbox One
1. Align the Energy Provide Unit
Fastidiously align the ability provide unit with the corresponding port on the motherboard. Be sure that the connector is securely seated.
2. Safe the Energy Provide Unit
Tighten the screws that maintain the ability provide unit in place. Use a screwdriver to use even strain.
3. Set up the Optical Drive
If you happen to eliminated the optical drive, insert it again into the Xbox One. Align the drive with the mounting factors and slide it into place.
4. Join the Optical Drive Cables
Join the optical drive knowledge and energy cables to the respective headers on the motherboard.
5. Set up the Onerous Drive
If you happen to changed the laborious drive, insert it into the interior bay. Join the info and energy cables to the suitable connectors.
6. Set up the Motherboard
Align the motherboard with the standoffs on the chassis and thoroughly decrease it into place.
7. Safe the Motherboard
Tighten the screws that safe the motherboard to the chassis. Use a screwdriver to use even strain.
8. Join the Entrance Panel Cables
Reconnect the entrance panel cables, together with the ability button, eject button, and USB ports, to their respective headers on the motherboard.
9. Set up the Fan
Place the fan again into its designated place on prime of the heatsink. Join the fan cable to the header on the motherboard.
10. Connect the High Cowl
Place the highest cowl on the Xbox One and align it with the chassis. Press down gently to safe the quilt in place. Use the screws eliminated earlier to tighten the quilt additional. Be sure that the screws are evenly tightened to stop harm or warping.
How To Open Xbox 1
To open an Xbox One, you have to a Torx T10 screwdriver. Upon getting the screwdriver, comply with these steps:
- Flip off the Xbox One and unplug it from the ability outlet.
- Place the Xbox One the wrong way up on a tender floor.
- Find the 2 Torx T10 screws on the underside of the Xbox One. These screws are situated close to the entrance of the console.
- Use the Torx T10 screwdriver to take away the 2 screws.
- As soon as the screws are eliminated, you possibly can raise the underside panel of the Xbox One up and off. Watch out to not harm the wires which are linked to the underside panel.
- As soon as the underside panel is eliminated, you’ll have entry to the within of the Xbox One. Now you can carry out any repairs or upkeep that you’ll want to.
Folks additionally ask about How To Open Xbox 1
Can I open my Xbox One with no screwdriver?
No. You will want a Torx T10 screwdriver to open an Xbox One.
Is it tough to open an Xbox One?
No. Opening an Xbox One is a comparatively easy course of. Simply comply with the steps outlined above and you must be capable to do it with none issues.
What ought to I do if I harm my Xbox One whereas opening it?
If you happen to harm your Xbox One whereas opening it, you must cease and phone Microsoft assist. They are going to be in a position that will help you troubleshoot the issue and get your Xbox One repaired.
