Changing a trunk lid on a Buick Lacrosse 2013 generally is a daunting activity, nevertheless it does not need to be. With the fitting instruments and a little bit endurance, you’ll be able to simply take away the previous trunk lid and set up a brand new one. This is a step-by-step information on the way to do it.
Earlier than you begin, collect the required instruments. You will want a socket wrench, a torx bit set, a flathead screwdriver, and a pair of pliers. After you have your instruments, you’ll be able to start the elimination course of. First, open the trunk and find the 2 bolts that maintain the trunk lid in place. These bolts are positioned on the within of the trunk, close to the highest. Take away the bolts utilizing the socket wrench.
As soon as the bolts have been eliminated, you’ll be able to fastidiously carry the trunk lid off of the hinges. Watch out to not harm the hinges or the paint on the trunk lid. As soon as the trunk lid is off, you’ll be able to disconnect {the electrical} connector for the trunk mild. This connector is positioned on the within of the trunk lid, close to the hinge. Use the flathead screwdriver to pry the connector aside. Now, you’ll be able to take away the trunk lid from the automobile.
Instruments and Preparation
Earlier than starting the method of eradicating the again of a 2013 Buick Lacrosse, it is essential to collect the required instruments and guarantee correct preparation:
Gathering the Important Instruments:
The next instruments are required for a profitable elimination:
- Phillips head screwdriver
- Flat head screwdriver
- Socket wrench set (10mm, 13mm, 15mm)
- Pry bar or a plastic trim device
- Electrical tape
Getting ready Your self and Your Car:
Earlier than beginning the elimination, it is important to take sure preparatory measures:
Moreover, it is really helpful to work in a well-lit space and put on acceptable security gear, equivalent to gloves and security glasses, to make sure a protected and efficient elimination course of.
Eradicating Exterior Trim
The outside trim in your Buick Lacrosse may be eliminated for quite a lot of causes, equivalent to to interchange it with a brand new one or to entry the inside of the automotive. Eradicating the outside trim is a comparatively easy course of that may be accomplished in just a few hours with the fitting instruments. Listed below are the steps concerned:
2. Take away the Window Trim
The window trim is held in place by a collection of clips. To take away the trim, you have to to make use of a trim elimination device to fastidiously pry the clips unfastened. Begin at one finish of the trim and work your method across the window. Watch out to not harm the paint or the trim itself.
Instruments you have to:
| Trim elimination device | |
| Gloves | |
| Security glasses |
Directions:
1. Placed on gloves and security glasses.
2. Insert the trim elimination device into the hole between the window trim and the door body.
3. Rigorously pry the trim unfastened from the clips.
4. Repeat steps 2 and three till the trim is totally eliminated.
Accessing the Rear Window
Take away the Trunk Liner
- Open the trunk and find the trunk liner.
- Use a flathead screwdriver or trim elimination device to pry the trunk liner unfastened from the trunk lid.
- As soon as the trunk liner is unfastened, fastidiously take away it from the trunk.
Disconnect the Electrical Connectors
- Find {the electrical} connectors which can be related to the rear window.
- Press the discharge tabs on the connectors and disconnect them.
- Watch out to not harm {the electrical} connectors or wiring.
Take away the Rear Window
- Use a 10mm socket wrench to take away the window actuator bolts.
- As soon as the bolts are eliminated, the window actuator will probably be unfastened.
- Grip the window actuator and pull it straight as much as take away it from the rear window.
| Half | Amount |
|---|---|
| 10mm Socket Wrench | 1 |
| Flathead Screwdriver or Trim Elimination Instrument | 1 |
Detaching the Rear Window Gasket
Eradicating the rear window gasket from a Buick Lacrosse 2013 entails cautious dealing with and the usage of specialised instruments. Listed below are the detailed steps to detach the rear window gasket:
1. Collect mandatory instruments:
- Plastic trim elimination device
- Adhesive cleaner
- Tender fabric
2. Place the automobile:
Park the Buick Lacrosse on a degree floor and interact the parking brake for security.
3. Entry the gasket:
Open the trunk and take away the inside trim panel on the rear hatch to entry the rear window gasket.
4. Eradicating the gasket:
Step 1: Loosen the gasket:
Rigorously insert the plastic trim elimination device into the groove between the gasket and the window body. Gently pry the gasket unfastened by sliding the device alongside the groove.
Step 2: Apply adhesive cleaner:
Apply a small quantity of adhesive cleaner to a comfortable fabric. Gently wipe the uncovered floor of the gasket the place it was loosened to take away any residual adhesive.
Step 3: Proceed prying and cleansing:
Proceed utilizing the plastic trim elimination device to pry the gasket unfastened alongside all the perimeter of the window body. Wipe any adhesive residue with the adhesive cleaner-dampened fabric as you progress.
Eradicating the Window Motor
The window motor is positioned on the within of the door panel. To entry it, you have to to take away the door panel by following these steps:
- Take away the screws which can be holding the door panel in place.
- Gently pry the door panel away from the door.
- Disconnect {the electrical} connectors which can be related to the door panel.
- Take away the door panel.
As soon as the door panel is eliminated, you will notice the window motor. It’s held in place by three bolts. Take away the bolts and disconnect {the electrical} connector that’s related to the window motor. The window motor can then be eliminated.
| 12 months | Half Quantity |
|---|---|
| 2010-2013 | 15876267 |
| 2014-2016 | 15876435 |
To interchange the window motor, merely reverse the steps above. You should definitely join {the electrical} connector to the window motor earlier than you bolt it in place.
Disconnecting the Wiper System
Find the wiper motor meeting, which is usually located beneath the rear window. Disconnect {the electrical} harness connector from the wiper motor by urgent the discharge tab and pulling the connector straight off.
Subsequent, determine the wiper arm retaining nuts, which safe the wiper arms to the wiper pivots. Utilizing a wrench or socket, fastidiously loosen and take away these nuts.
Now, gently carry the wiper arms straight up and off the wiper pivots. Be conscious to not harm the wiper blades or the pivots.
Disconnect the wiper pivots from the wiper motor linkage. This will likely contain unbolting the pivots or releasing them from a locking mechanism.
Take away the wiper motor meeting from the automobile by unbolting it from its mounting factors. Chances are you’ll have to take away the rear window trim or molding to entry the mounting factors.
Lastly, examine the wiper motor meeting, wiper arms, and pivots for any harm or put on. Substitute any broken parts as mandatory earlier than reassembling the system.
Unbolting the Rear Panel
As soon as the door panel is eliminated, it is time to unbolt the rear panel.
- Use a socket wrench to take away the nuts holding the rear panel in place.
- Rigorously carry the rear panel up and away from the door.
- Disconnect any electrical connectors which can be connected to the rear panel.
- Take away the window regulator from the rear panel.
- Take away the door lock actuator from the rear panel.
- Take away the opposite parts which can be connected to the rear panel, such because the door deal with and lock cylinder.
- Unbolting the Lock Cylinder:
- Find the 2 bolts that maintain the lock cylinder in place.
- Use a socket wrench to take away the bolts.
- Rigorously pull the lock cylinder out of the door.
- Disconnect {the electrical} connector from the lock cylinder.
Lifting Off the Rear Panel
To carry off the rear panel, you will want just a few instruments: a flat-head screwdriver, a Phillips head screwdriver, and a trim elimination device.
Begin by eradicating the 2 screws which can be positioned on the backside of the rear panel utilizing Phillips head screwdriver, then use your flat-head screwdriver to fastidiously pry up the panel from the underside and work your method across the edges. For those who encounter any resistance, use the trim elimination device to softly launch the clips which can be holding the panel in place.
Step-by-Step Directions to Carry Off the Rear Panel
| Step | Description |
|---|---|
| 1 | Take away the 2 screws on the backside of the rear panel. |
| 2 | Pry up the panel from the underside utilizing a flat-head screwdriver and work your method across the edges. |
| 3 | Use the trim elimination device to launch any clips which can be holding the panel in place. |
| 4 | Carry the rear panel off the automobile. |
Changing the Rear Panel
9. Eradicating the Fender
- Disconnect {the electrical} connector positioned on the rear of the fender.
- Take away the bolts securing the fender to the physique.
- Rigorously pull the fender away from the physique, disconnecting any remaining electrical connectors or hoses.
Further Particulars for Subsection 9: Eradicating the Fender
Earlier than eradicating the fender, make sure that all electrical connectors are disconnected to forestall harm. Take warning when pulling the fender away from the physique, as it could be held in place by clips or different fasteners. Examine the world across the fender for any hidden bolts or screws that will should be eliminated.
| Instruments Required: |
|---|
| Socket wrench or ratchet |
| Screwdriver |
| Torx bit set (optionally available) |
Reassembly Issues
10. Be Affected person and Reassemble Methodically
Reassembling the rear seat of the Buick Lacrosse 2013 requires endurance and precision. Observe the steps in reverse order, making certain that every element is appropriately positioned and secured. Keep away from speeding by way of the method, as improper reassembly can compromise the match, performance, and security of the rear seat.
Here’s a extra detailed rationalization of the way to reassemble the rear seat of the Buick Lacrosse 2013:
| Step | Description |
|---|---|
| 10.1 | Make sure that the seat cushion and backrest are appropriately aligned and secured. |
| 10.2 | Reattach the headrests and guarantee they’re correctly seated. |
| 10.3 | Set up any trim items or panels that had been eliminated throughout disassembly. |
| 10.4 | Reconnected {the electrical} connectors for the heated seats or different electrical parts. |
| 10.5 | Double-check all fastenings and bolts to make sure they’re correctly tightened. |
Take Off the Again of a 2013 Buick Lacrosse
Eradicating the again of a 2013 Buick Lacrosse is a comparatively easy course of that may be accomplished in just a few steps. Listed below are the steps on the way to take off the again of a 2013 Buick Lacrosse:
- Open the trunk of the Lacrosse.
- Find the 2 bolts that maintain the again of the seat in place. The bolts are positioned on both aspect of the seat.
- Take away the bolts utilizing a wrench or socket.
- Gently pull the again of the seat up and out of the Lacrosse.
Folks Additionally Ask About Take Off the Again of a 2013 Buick Lacrosse
How do you take away the again seat of a 2013 Buick Lacrosse?
To take away the again seat of a 2013 Buick Lacrosse, first take away the headrests from the seats. Then, find the 2 levers on the underside of the seat cushion. Pull up on the levers and carry the seat cushion up and out of the Lacrosse.
How do you take away the trunk lid of a 2013 Buick Lacrosse?
To take away the trunk lid of a 2013 Buick Lacrosse, first open the trunk. Then, find the 2 bolts that maintain the trunk lid in place. The bolts are positioned on both aspect of the trunk lid. Take away the bolts utilizing a wrench or socket. Carry the trunk lid up and off of the Lacrosse.
